Поз.
Артикул
Описание
1
INJECTION PUMP FROM ENGINE 5516036
2
STOP ANGLE FOR CHOKE AND STOPPER CABLE AT INJECTION PUMP FROM ENGINE 5516036
3
PRESSURE VALVE WITH VALVE SUPPORT
4
COIL SPRING FOR PRESSURE VALVE
6
PIPE CONNECTION. FITTING
7
CLAMPING JAW WITH THREAD. CLAMPING PIECE , Replaced By: A0000781435, +001A0000781335
8
CLAMPING JAW. CLAMPING PIECE , Replaced By: A0000781335, +001A0000781435
11
BREATHER SCREW. SCREW , Replaced By: A0000741771
17
OIL DIPSTICK FRONT, FOR INJECTION PUMPS 007 074 53 02 002 074 34 01 002 074 13 01 002 074 65 01 002 074 91 01 002 074 77 01 002 074 87 01 003 074 47 01 003 074 58 01
18
BREATHER FILTER. FILTER TRAILER CONTROL VALVE,CONNECTION: "4"
20
DIAPHRAGM FOR GOVERNOR, FOR INJECTION PUMP 002 074 01 01 UND 002 074 02 01
25
FUEL PUMP WITHOUT PRE-FILTER
26
VALVE , Replaced By: A0000910910
27
PRESSURE SPRING. VALVE SPRING
28
SCREW PLUG
29
HAND PUMP. FUEL PUMP , Replaced By: A0000904050
35
GASKET , Replaced By: A0000911280
39
CONTROL LEVER ON CONTROL SHAFT TO INJECTION PUMP
51
FOLLOWER. MITNEHMER FUR EINSPRITZPUMPE
56
GASKET BETWEEN TIMING GEAR CASE COVER AND INJECTION PUMP
61
DRIVE SHAFT UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T
62
SPACER TUBE BETWEEN GROOVED BEARINGS ON DRIVE SHAFT FROM ENGINE 4505075
63
ADJUSTING RING FOR DRIVE SHAFT FROM ENGINE 4505075-5514611
65
INJECTION TIMING GEAR FROM ENGINE 5514612
66
SEGMENT FLANGE. SEGMENT PLATE ,910 030606936 000166 : 918 000385
67
BALANCING WEIGHT. BALANCE WEIGHT
68
SEGMENT PLATE
69
PIN , Replaced By: A6150750074
70
PRESSURE SPRING. SPRING , 918 000385 936 000219 937 043952 938 014499 939 023012 940 10/50,20/60 140322 940 12/52,22/62 004658
71
PIN , 918 000385 936 000219 937 043952 938 014499 939 023012 940 10/50,20/60 140322 940 12/52,22/62 004658
72
DRIVE GEAR FROM ENGINE 5514612
73
BUSHING
76
THRUST WASHER
80
COUPLING SLEEVE FOR INJECTION PUMP DRIVE FROM ENGINE 4500146
81
SNAP RING IN COUPLING SLEEVE
82
NOZZLE HOLDER WITH INJECTION NOZZLE
83
THROUGH FITTING. CONNECTOR , 910 033404 930 000062 912 10/50,20/60 107671 912 12/52,22/62 011323 913 10/50,20/60 053390 913 12/52,22/62 001617
84
HEX. NUT. NUT , 910 033404 930 000062 912 10/50,20/60 107671 912 12/52,22/62 011323 913 10/50,20/60 053390 913 12/52,22/62 001617
85
SHIM, 1.0 MM THICK. SPACER WASHER1.0 MM
86
PRESSURE SPRING
87
THRUST BOLT. PIN , Replaced By: A0000170374
88
NOZZLE HOLDER ELEMENT. INSERT
89
BOX NUT. UNION NUT , 910 033404 930 000062 912 10/50,20/60 107671 912 12/52,22/62 011323 913 10/50,20/60 053390 913 12/52,22/62 001617
92
INJECTION NOZZLE. NOZZLE
93
GASKET. SEAL WASHER , Replaced By: A6170170260
100
PRESSURE PIPE, BENT FOR CYLINDER 1 FROM INJECTION PUMP TO NOZZLE HOLDER
101
PRESSURE PIPE, BENT FOR CYLINDER 2 FROM INJECTION PUMP TO NOZZLE HOLDER
102
PRESSURE PIPE, BENT FOR CYLINDER 3 FROM INJECTION PUMP TO NOZZLE HOLDER FROM ENGINE 8516776
103
PRESSURE PIPE, BENT FOR CYLINDER 4 FROM INJECTION PUMP TO NOZZLE HOLDER FROM ENGINE 8516776
104
PIPE CLAMP FOR PRESSURE LINES 1, 2, 3 AND 4 UP TO ENGINE 4507500
108
PIPE BRACKET FOR FUEL PIPE, CYLINDERS 1 AND 2, AT WATER PUMP
109
PIPE CLAMP FOR PRESSURE PIPE 1 AND 2 AND VACUUM LINE AT WATER PUMP
113
PIPE BRACKET FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD FROM ENGINE 6501469
114
RUBBER PAD BETWEEN VACUUM PIPE AND CYLINDER HEAD
115
LEAK LINE
116
BRACKET, T-FITTING AT TIMING GEAR CASE COVER FROM ENGINE 7507991
999
NOZZLE HOLDER ELEMENT , Replaced By: A0000170122
999
THRUST BOLT IN NOZZLE HOLDER, Replaced By: A0000170274
999
THROUGH FITTING FOR CONNECTION OF LEAK OIL LINE, Replaced By: A0000170654
999
SHIM, 1.10 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000173852
999
SHIM, 1.15 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000173952
999
SHIM, 1.20 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174052
999
SHIM, 1.25 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174152
999
INJECTION NOZZLE FOR ENGINES WITH AN ESPECIALLY STROG DIESEL KNOCK
999
SHIM, 1.30 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174252
999
SHIM, 1.35 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174352
999
SHIM, 1.40 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174452
999
SHIM, 1.45 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174552
999
SHIM, 1.50 MM THICK. SPACER WASHER1.70 MM
999
SHIM, 1.55 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174752
999
SHIM, 1.60 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174852
999
SHIM, 1.65 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000174952
999
SHIM, 1.70 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000175052
999
SHIM, 1.75 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000175152
999
SHIM, 1.80 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000175252
999
SHIM, 1.0 MM THICK FOR ADJUSTMENT OF INJECTION PRESSURE, Replaced By: A0000173652
999
SHIM, 1.05 MM THICK. UNTERLEGSCHEIBE 1,05-MM STARK ZUR EINSTELLUNG DES EINSPRITZDRUCKES
999
NOZZLE HOLDER BODY. NOZZLE HOLDER UPPER PART TO 000 017 55 21
999
SHIM, 1.05 MM THICK. SPACER WASHER1.04 MM,TO 002 017 03 21,002 017 35 21, TO NOZZLE HOLDER OF MAKE: BOSCH
999
SHIM, 1.10 MM THICK. SPACER WASHER1.1 MM
999
SHIM, 1.15 MM THICK. SPACER WASHER1.15 MM
999
SHIM, 1.20 MM THICK. SPACER WASHER1.2 MM
999
SHIM, 1.25 MM THICK. SPACER WASHER1.24 MM
999
SHIM, 1.30 MM THICK. SPACER WASHER1.3 MM
999
SHIM, 1.35 MM THICK. SPACER WASHER1.34 MM, Replaced By: A0030177852
999
SHIM, 1.40 MM THICK. SPACER WASHER , Replaced By: A0030178452
999
SHIM, 1.45 MM THICK. SPACER WASHER1.45 MM
999
SHIM, 1.50 MM THICK. SPACER WASHER1.50 MM, Replaced By: A0030179452
999
SHIM, 1.55 MM THICK. SPACER WASHER1.55 MM
999
SHIM, 1.60 MM THICK. SPACER WASHER1.6 MM
999
SHIM, 1.65 MM THICK. SPACER WASHER1.65 MM
999
SHIM, 1.70 MM THICK. SPACER WASHER , Replaced By: A0040171452
999
SHIM, 1.75 MM THICK. SPACER WASHER1.75 MM
999
SHIM, 1.80 MM THICK. SPACER WASHER1.80 MM, Replaced By: A0040172452
999
SHIM, 1.85 MM THICK. SPACER WASHER , Replaced By: A0040172852
999
SHIM, 1.90 MM THICK. SPACER WASHER1.9 MM
999
SHIM, 1.95 MM THICK. SPACER WASHER1.95 MM
999
BREATHER SCREW ON INJECTION PUMP, FRONT SIDE, Replaced By: A0000740671
999
OIL DIPSTICK , Replaced By: A0000741360
999
REPLACED BY 002 074 01 01 TOGETHER WITH 1 STOP ANGLE 636 074 02 40 UP TO ENGINE 5516035
999
DIAPHRAGM FOR GOVERNOR, FOR INJECTION PUMP 000 074 93 02 UND 001 074 34 01
999
DIAPHRAGM FOR GOVERNOR, FOR INJECTION PUMP 001 074 54 01 UND 001 074 77 01
999
CLAMPING JAW WITH THREAD TO CLAMP PIPE CONNECTIONS, Replaced By: A0000780335
999
SEALING RING FOR PIPE CONNECTIONS, Replaced By: A0019973040
999
, Replaced By: A0020740201
999
INJECTION PUMP , Replaced By: A0020740101
999
INJECTION PUMP , Replaced By: A0020740201
999
INJECTION PUMP , SPECIAL REQUEST FOR COUNTRIES MORE THAN 2000 M HIGH
999
REPLACED BY. DICHTUNG ZWISCHEN DUSENHALTER UND VORKAMMER
999
FIXING SCREW WITH TIMING NEEDLE UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 0
999
COVER FOR TIMING GEAR CASE COVER OR INJECTION TIMING GEAR RESP. AB MOTOR 5514612
999
BRACKET, T-FITTING AT TIMING GEAR CASE COVER, Replaced By: A6360700140
999
FROM ENGINE 5514612, Replaced By: A6360750350
999
UNIT PARTS FOR SUBSEQUENT INSTALLATION OF INJECTION TIMING GEAR UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDIT
999
BRACKET, T-FITTING AT TIMING GEAR CASE COVER UP TO ENGINE 7507990
999
, Replaced By: A6360701235
999
LEAK LINE , Replaced By: A6360701235
999
REPLACED BY. DRUCKLEITUNG GEBOGEN FUR ZYLINDER 3 VON DER EINSPRITZPUMPE ZUM DUSENHALTER
999
REPLACED BY. DRUCKLEITUNG GEBOGEN FUR ZYLINDER 4 VON DER EINSPRITZPUMPE ZUM DUSENHALTER
999
STOP ANGLE FOR CHOKE AND STOPPER CABLE AT INJECTION PUMP UP TO ENGINE 5516035
999
BUSHING FOR DRIVE GEAR FROM ENGINE 5514612, Replaced By: A6360750350
999
PIN FOR TIMING LIMIT, Replaced By: A6210750174
999
PIN FOR SPRING SEAT, Replaced By: A6210750274
999
SPACER TUBE BETWEEN GROOVED BEARINGS ON DRIVE SHAFT UP TO ENGINE 4500145
999
COUPLING SLEEVE. KUPPLUNGSHULSE FUR EINSPRITZPUMPEN-ANTRIEB
999
DRIVE SHAFT FOR INJECTION PUMP UP TO ENGINE 4505074
999
DRIVE GEAR, 40 TEETH. ANTRIEBSRAD 40 ZAHNE FUR EINSPRITZPUMPE
999
SPACER TUBE BETWEEN GROOVED BEARINGS ON DRIVE SHAFT FROM ENGINE 4500146-4505074
999
DRIVE SHAFT
999
PIPE BRACKET. ROHRHALTER FUR KRAFTSTOFFLEITUNG ZYLINDER 1 UND 2 AN WASSERPUMPE
999
PIPE BRACKET FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD, Replaced By: A6360780285
999
SHIM UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T
999
PRESSURE SPRING FROM ENGINE 5514612, Replaced By: A6369930501