Поз.
Артикул
Описание
1
CRANKSHAFT WITH COUNTERWEIGHT AND FLYWHEEL
2
SPACER RING, 5.45-MM THICK FOR VIBRATION DAMPER AT CRANKSHAFT OPTIONAL
4
CRANKSHAFT GEAR. KURBELWELLENRAD 20 ZAHNE FUR STEUERUNGSANTRIEB AB MOTOR-NR. 00097/52
5
OIL SLINGER RING ON CRANKSHAFT, FRONT
8
FLYWHEEL WITH RING GEAR. FLYWHEEL WITH
9
STARTER RING
10
EXPANDING SCREW FOR FLYWHEEL AT CRANKSHAFT
13
COLLAR SCREW
14
SEALING RING AT CRANKSHAFT, FRONT
15
PULLEY
17
LOCKING RING. VERSCHLUSSDECKEL IN DER KURBELWELLE HINTEN FUR GETRIEBE-ANTRIEBSWELLE
20
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 70-MMSTANDARD OPTIONAL GLYCO READY FOR INSTALLATION
21
CRANKSHAFT BEARING SHELL MAKE GLYCO WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B
22
CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING
25
CONNECTING ROD
26
CONNECTING BUSHING
27
CONNECTING ROD SCREW FROM ENGINE 5511622
28
NUT , UP TO ENGINE 920 10/50,20/60 073205 920 12/52,22/62 019059 921 003475 923 10/50,20/60 092627 923 12/52,22/62 015750 UP TO ENGINE 924 10/50,20/60 002127 924 12/52,22/62 000138 926 10/50,20/60 004380 926 12/52,22/62 000145 UP TO ENGINE 927 000685 928 000871 929 000007
29
CONNECTING ROD BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL
34
PISTON WITH PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.00STANDARD MAKE MAHLE OPTIONAL
35
COMPRESSION RING FOR GROOVE I
36
TAPERED COMPRESSION. MINUTENRING FUR NUTE II
37
NOVIX STEPPED RING FOR GROOVE III
38
NOVIX-SLOTTED RING. NOVIX SLOTTED RING GROOVE IV
999
NOVIX STEPPED RING FOR GROOVE III
999
NOVIX STEPPED RING FOR GROOVE III
999
NOVIX STEPPED RING FOR GROOVE III
999
NOVIX STEPPED RING FOR GROOVE III
999
NOVIX SLOTTED RING. NOVIX-SCHLITZRING MIT STUTZRING FUR NUTE IV
999
NOVIX SLOTTED RING. NOVIX-SCHLITZRING MIT STUTZRING FUR NUTE IV
999
NOVIX SLOTTED RING. NOVIX-SCHLITZRING MIT STUTZRING FUR NUTE IV
999
NOVIX SLOTTED RING FOR GROOVE IV
999
COMPRESSION RING GROOVE I
999
COMPRESSION RING GROOVE I
999
COMPRESSION RING GROOVE I
999
COMPRESSION RING GROOVE I
999
TAPERED COMPRESSION. MINUTENRING FUR NUTE II
999
TAPERED COMPRESSION. MINUTENRING FUR NUTE II
999
TAPERED COMPRESSION. MINUTENRING FUR NUTE II
999
TAPERED COMPRESSION. MINUTENRING FUR NUTE II
999
FLYWHEEL WITH , Replaced By: A1210300805
999
PISTON WITH PIN AND RINGS, CYLINDER DIA. 85.25-MMREP. SIZE I
999
PISTON WITH PIN AND RINGS, CYLINDER DIA. 85.50-MMREP. SIZE II
999
PISTON WITH PISTON PIN AND PISTON RINGS, CYLINDER DIA. 86.00REPAIR SIZE III MAKE MAHLE OPTIONAL
999
PISTON WITH PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA. 86.50 MM REPAIR SIZE IV. OPTIONAL
999
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.75-MMREPAIR SIZE I MAKE GLYCO OPTIONAL READY FOR INSTALLATION
999
SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MMREPAIR SIZE II MAKE GLYCO OPTIONAL READY FOR INSTALLATION
999
PISTON WITH PISTON PIN AND PISTON RINGS MAKE NURAL FOR CYLINDER DIA.85.00 MMSTANDARD OPTIONAL
999
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.25-MMREPAIR SIZE III MAKE GLYCO OPTIONAL READY FOR INSTALLATION
999
PISTON WITH PISTON PIN AND PISTON RINGS MAKE NURAL FOR CYLINDER DIA. 85.25 MM REPAIR SIZE I. OPTIONAL
999
SET OF CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. 69.00 MM REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL
999
PISTON WITH PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.50REPAIR SIZE II MAKE NURAL OPTIONAL
999
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 70-MMSTANDARD OPTIONAL VANDERVELL READY FOR INSTALLATION
999
PISTON WITH PISTON PIN AND PISTON RINGS, MAKE NURAL FOR CYLINDER DIA. 86.00 MMREPAIR SIZE III. OPTIONAL
999
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.75-MMREPAIR SIZE I MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION
999
PISTON WITH PISTON PIN AND PISTON RINGS, MAKE NURAL FOR CYLINDER DIA. 86.50 MM REPAIR SIZE IV. OPTIONAL
999
SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MMREPAIR SIZE II MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION
999
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.25-MMREPAIR SIZE III MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION
999
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.00-MMREPAIR SIZE IV VANDERVELL READY FOR INSTALLATION
999
CRANKSHAFT WITH COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS LAUCHERTHAL OPTIONAL
999
CRANKSHAFT WITH COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS GLYCO OPTIONAL
999
SPACER RING FOR CRANKSHAFT, OIL SLINGER RING FROM ENGINE 75 11544 IN ADDITION MOUNTED IN 75 11374 TO 75 11423
999
SPACER SLEEVE IN CRANKSHAFT FOR GROOVED BEARING UP TO ENGINE 6510419
999
REPLACED BY 121 031 03 07 TOGETHER WITH 1 SPACER RING 121 031 00 51 UP TO ENGINE 75 11543 WITH EXCEPTION OF 75 11374 TO 75 11423
999
COUNTERWEIGHT
999
ADJUSTING NEEDLE FOR ADJUSTING TOP DEAD CENTER
999
CRANKSHAFT BEARING SHELL GLYCO WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER BEARIN
999
CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING
999
CRANKSHAFT BEARING SHELL MAKE GLYCO WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B
999
CRANKSHAFT BEARING SHELL GLYCO WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING
999
CRANKSHAFT BEARING SHELL MAKE GLYCO WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B
999
CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING
999
CRANKSHAFT BEARING SHELL MAKE GLYCO WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B
999
CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING
999
CRANKSHAFT BEARING SHELL MAKE VANDERVELL WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN
999
CRANKSHAFT BEARING SHELL VANDERVELL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING
999
CRANKSHAFT BEARING SHELL VANDERVELL WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER B
999
CRANKSHAFT BEARING SHELL VANDERVELL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING
999
CRANKSHAFT BEARING SHELL MAKE VANDERVELL WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN
999
CRANKSHAFT BEARING SHELL VANDERVELL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING
999
CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING)
999
CRANKSHAFT BEARING SHELL VANDERVELL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING
999
CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING)
999
CRANKSHAFT BEARING SHELL VANDERVELL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING
999
CONNECTING ROD BEARING SHELL LAUCHERTHAL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL
999
CONNECTING ROD BEARING SHELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL, Replaced By: A1210380710
999
CONNECTING ROD BEARING SHELL HALF, INNER DIA. 51.75-MMREPAIR SIZE I LAUCHERTHAL OPTIONAL
999
CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.75-MMREPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL, Replaced By: A1210380810
999
CONNECTING ROD BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10
999
CONNECTING ROD BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10, Replaced By: A1210380910
999
CONNECTING ROD BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.25 MMREPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL
999
CONNECTING ROD BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL, Replaced By: A1210381010
999
CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MMREPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL
999
CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MMREPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL, Replaced By: A1210381110
999
CONNECTING ROD BEARING SHELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL, Replaced By: A1210382810
999
CONNECTING ROD BEARING SHELL GLYCO INTERIOR DIA. 51.75 MMREPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL
999
CONNECTING ROD BEARING SHELL REPAIR SIZE I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL, Replaced By: A1210382910
999
CONNECTING ROD BEARING SHELL HALF, INNER DIA. 51.50-MMREPAIR SIZE II GLYCO OPTIONAL
999
CONNECTING ROD BEARING SHELL INTERIOR DIA. 51.50 MMREPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL, Replaced By: A1210383010
999
CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.25-MMREPAIR SIZE III OPTIONAL
999
CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.25-MMREPAIR SIZE III OPTIONAL, Replaced By: A1210383110
999
CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MMREPAIR SIZE IV MAKE GLYCO OPTIONAL
999
CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MMREPAIR SIZE IV MAKE GLYCO OPTIONAL, Replaced By: A1210383210
999
CONNECTING ROD BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL
999
CONNECTING ROD BEARING SHELL VANDERVELL INTERIOR DIA. 51.75 MMREPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL
999
CONNECTING ROD BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10
999
CONNECTING ROD BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL
999
CONNECTING ROD BEARING SHELL HALF, INNER DIA. 51.00-MMREPAIR SIZE IV VANDERVELL OPTIONAL
999
PULLEY , Replaced By: A1212000105
999
WASHER FOR HUB, PULLEY UP TO ENGINE 6500024
999
SPACER RING,. AUSGLEICHRING 5,60 MM ST. WAHLWEISE ZWISCHEN KURBELWELLENRAD UND KURBELWELLE
999
SPACER RING,. AUSGLEICHRING 5,75 MM ST. WAHLWEISE ZWISCHEN KURBELWELLENRAD UND KURBELWELLE
999
SPACER RING,. SHIM, 5.90 MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT
999
SPACER RING,. SHIM, 6.05 MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT
999
CONNECTING BUSHING, OUTER DIA.28.5-MM REPAIRS
999
SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MMSTANDARD(MAKE LAUCHERTHAL) OPTIONAL READY FOR INSTALLATION
999
SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MMREPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION
999
SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MMREPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION
999
SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.25-MMREPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION
999
SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MMREPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION
999
CRANKSHAFT BEARING SHELL MAKE LAUCHERTHAL WITH GROOVE,USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN
999
CRANKSHAFT BEARING SHELL MAKE LAUCHERTHAL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE, USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE
999
CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE, USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL